98391000 REV. REL 1302 WEST BEARDSLEY AVENUE P.O. BOX 1127 ELKHART IN 46515 (574) 295-8330 FAX (574) 293-9914 © 2012 ELKHART BRASS MFG. C
EXM UHP– Installation Instructions (Step 2 – Configure the System) 10 Installation Step 2: Configure the EXM System Obtaining the EXM Configuration
EXM UHP– Installation Instructions (Step 2 – Configure the System) 11 Under the Monitor Settings tab,
EXM UHP– Installation Instructions (Step 2 – Configure the System) 12 On the Input Controllers tab, e
EXM UHP– Installation Instructions (Step 2 – Configure the System) 13 10 Go to the Save Settings tab
EXM UHP– Installation Instructions (Calibrate the EXM System) 14 Installation Step 3: Calibrate the EXM System After successfully configuring the sy
EXM UHP– Installation Instructions (Calibrate the EXM System) 15 o Press and hold PRESET and then press either the LEFT or RIGHT button. (On the joy
EXM UHP– Operating Instructions 16 Operating Instructions - In this section the reader will be guided through basic operation of the EXM system. A
EXM UHP– Operating Instructions 17 C. Re-calibrating Horizontal and Vertical Rotation Calibrating the EXM system’s horizontal and vertical rotation
EXM UHP– Operating Instructions 18 E. Keep-Out Zones Keep-Out Zones are used when it is desired to restrict the motion of the monitor to a smaller m
EXM UHP– Operating Instructions 19 F. Stow Position The Stow Position is a preset position that can be used to bring the monitor into a position sui
EXM UHP – Table of Contents 2 Table of Contents – Product Safety Information……………………………………………………….…………..3 System Components…………………………………………………………….
EXM UHP– Operating Instructions 20 H. Clear All Function The Clear All Function allows the user to remove any Travel Limits, Keep-Out Zones, or Stow
EXM UHP– Operating Instructions 21 K. Write Diagnostic File Remove the USB cover from any input controller. Install a blank USB flash drive i
EXM UHP– Operating Instructions 22 o Once all of the input controllers are updated and there were no errors while upgrading; then the preset LED wil
EXM UHP– Monitor Callout Drawing 23 Maintenance Instructions - In this section, the reader will be instructed on how to properly care for their EXM
EXM UHP– Monitor Callout Drawing 24 System Specifications – A. Panel Mount Controller Input power 12/24 VDC (11 VDC to 27 VDC) Electrical Lo
EXM UHP– Monitor Callout Drawing 25 Monitor Callout Drawing – Figure 1: 7161 EXM UHP Monitor 5000 Series
EXM UHP– Component Mounting Templates 26 Interpreting Flow Data The following graphs offer the pressure losses for the monitor (and other devices) in
EXM UHP– Component Mounting Templates 27 Component Mounting Templates – OEM Interface Module Mountin
EXM UHP– Component Mounting Templates 28 Joystick Controller Mounting Template
EXM UHP– Component Mounting Templates 29 NOTES:______________________________________________________________________________________________________
EXM UHP– Product Safety Information 3 Product Safety Information - 1. All personnel who may be expected to use this equipment must be thoroughly t
EXM UHP– System Components 4 System Components - In this section, the reader will be introduced to the various EXM system components. The reader’
EXM UHP– System Components 5 C. OEM Interface Module - 7070 The OEM Interface Module is used in conjunction with either the Elkhart Brass or custo
EXM UHP– Installation Instructions (Installation Overview) 6 Installation Instructions - In this section, the reader will be guided through the ste
EXM UHP– Installation Instructions (Step 1 – Mount and Wire All System Components) 7 Installation Step 1: Mount and Wire All System Components Insta
EXM UHP– Installation Instructions (Step 1 – Mount and Wire All System Components) 8 B. Joystick Controller and OEM Interface Module – Using the
EXM UHP– Installation Instructions (Step 1 – Mount and Wire All System Components) 9 C. Nozzles – Ensure there is a gasket inside the nozzle swiv
Comments to this Manuals